|
This topic describes how to configure
an Ethernet-over-ATM (EoA) interface on the Voyager 205, if one is needed
to communicate with your ISP. This interface is also commonly referred
to as an RFC1483 interface, for the name of the Internet specification
to which it conforms.
The Ethernet-over-ATM (EoA) protocol is commonly used to carry data between local area networks
that use the Ethernet protocol and wide-area networks that use the ATM protocol.
Many telecommunications industry networks use the ATM protocol. ISPs who provide
DSL services often use the EoA protocol for data transfer with their customers'
DSL modems.
EoA can be implemented to provide a bridged connection between a DSL modem
and the ISP. In a bridged connection, data is shared between the ISP's network
and their customer's as if the networks were on the same physical LAN. Bridged
connections do not use the IP protocol. EoA can also be configured to provide a
routed connection with the ISP, which uses the IP protocol to exchange
data.
Before creating an EoA interface or modifying the default settings, contact
your ISP to determine which type of protocol they use.
PPP vs.
EoA: Your ISP may use a protocol other
than EoA for communication with your router, such as the
point-to-point protocol (PPP). One type of PPP, named PPP over Ethernet
(PPPoE), actually works "on top" of the EoA protocol. The other
type, PPP over ATM (PPPoA), does not. However, if your ISP uses either
type of PPP, you do not need to separately create an EoA interface. See the PPP
help topic for instructions on creating or configuring a PPP interface. |
Viewing Your EoA Setup
If the EoA configuration page is not already displaying, click the WAN
tab, and then click EoA in the task bar. The
EoA table contains a row for each EoA interface currently defined. The
table may contain no entries if your ISP does not use the EoA protocol. The
following table describes the fields on this page:
- Interface: The name the software uses to identify the EoA interface.
- Interface Sec Type: The type of security protections in effect on
the interface (public, private, or DMZ):
- A public interface connects to the Internet (IPoA interfaces
are typically public). Packets received on a public interface are
subject to the most restrictive set of firewall protections defined in
the software.
- A private interface connects to your LAN, such as the Ethernet
interface. Packets received on a private interface are subject to a less
restrictive set of protections, because they originate within the
network.
- The term DMZ (de-militarized zone), in Internet networking
terms, refers to computers that are available for both public and
in-network accesses (such as a company's public Web server). Packets
incoming on a DMZ interface -- whether from a LAN or external source --
are subject to a level of protection that is in between those for public and
private interfaces.
- Lower interface: EoA interfaces are defined in software, and then
associated with lower-level software and hardware structures (at the
lowest level, they are associated with a physical port - the WAN port).
This field should reflect an interface name defined in the next lower
level of software over which the EoA interface will operate. This will
be an ATM VC interface, such as aal5-0, as described in ATM
VC.
- Config IP Address and Net Mask: The IP address and network mask you
want to assign to the interface. If the interface will be used for bridging
with your ISP and you will not be using the device as a router on your LAN,
then you do not need to specify IP information. If you enable DHCP for this
interface, then the Configured IP address will serve only as a request to
the DHCP server. The actual address that is assigned by the ISP may differ
if this address is not available.
- Use DHCP: When enabled, this setting instructs the device to accept
IP information assigned dynamically by your ISP's DHCP server. If the
interface will be used for bridging with your ISP and you will not be
routing data through it, leave this checkbox unselected.
- Default Route: Indicates whether the Voyager 205 should use
the IP address assigned to this interface, if any, as its default route
for your LAN. This can be Enable or Disable. See
IP Routes for an explanation of default routes.
- Gateway Address: The external IP address that theVoyager 205
communicates with via the EoA interface to gain access to the Internet.
This is typically an ISP server.
- Status: A green or red ball will display to indicate that the
interface is currently up or down, respectively. You cannot
manually enable or disable the interface; a down interface may indicate
a problem with the DSL connection or the connection to the ISP's access
server.
- Action: Icons you can click on to edit (
)
or delete ( )
the associated EoA interface.
Adding EoA Interfaces
Follow these instructions to add an EoA interface:
- If the EoA page is not already displaying, click the WAN tab, and
then click EoA in the task bar.
- Click Add to display the EoA Interface - Add page.
- Select one of the predefined interface names from the EoA Interface drop
down list.
- From the Interface Sec Type drop-down list, select the level of IP Firewall to be
used on this interface, as defined above.
- In the Lower Interface field, select the lower-level interface name over
which this protocol is being configured.
If the interface will be used to provide only a bridged connection to your
ISP, skip to step 8.
- If you are creating the EoA interface to provide a routed Internet
connection, enter the IP address for the interface in the Conf. IP Address
field, and enter the network mask.
This address serves as the public IP address for your entire LAN and is
usually assigned by your ISP.
- If your ISP will assign the IP address from their DHCP server, click the
Enable radio button in the Use DHCP field.
When DHCP is enabled, the address you entered in the Conf. IP Address field
will be requested from the DHCP server; the server many assign a different
address if necessary.
- If you are using the EoA interface to provide a routed connection to your
ISP and you want the EoA interface to serve as the default route for
Internet access for your LAN, ensure that the Default Route: Enable radio
button is selected. (If you have more than on WAN interface, note that only
one of them can be specified as the default route.)
If you are using the interface to provide a bridged connection, then
deselect this field.
- In the Gateway IP Address field, enter the address of the Internet
computer to contact to gain initial access to the Internet.
- Click Apply. A page displays to confirm your changes.
- Click Close to return to the
EoA page and view the new interface in the table.
- If the interface will be used to provide only a routed connection to your
ISP, skip to step 16.
- If the interface will be used to provide a bridged-only connection or a
bridged-and-routed connection to your ISP, then continue with step 12 to
enable bridging.
- Click the Bridging tab.
- In the interface table, select all interface names on which you want to
perform bridging and click Add. To enable bridging with your ISP,
select the EoA interface and the LAN interface(s) (eth-0 and/or usb-0). You
can enable bridging on an IP-enabled EoA interface; in this case, the same
interface will be capable of handling both bridged and routed data packets.
- Click the Bridging: Enable/Disable link.
- Click the Bridging: Enabled radio button (if not already selected),
and then click Apply.
NOTE: If want your changes to be permanent, be sure to Save
them.
|